n
Very reasonable design but patience is needed during assembly
I bought the Jaspers 4R-150 with the intention of using it as a 3R stand, where the second tier would have additional support as per first tier. A spirit level is needed to properly arrange the assembly without frustration. Be careful to double-check your work before placing your machines, there are many points to tighten. Once assembled, the unit is excellent. I used shelving material across each tier with a 90 degree bracket on the front edge of each shelf to stop machines from sliding. With appropriate shelves and support, you will save money on the extra brackets for each piece of gear.
3
0
Report
K
Amaaaaazing
Amaaaaazing Stand...highly recommended... Tnx a lot
0
0
Report
A
Value for money
Used for two keyboards and desktop computer with large screen. The coresponding "studio" furniture is very expensive even to think about.
Top self was put in the back and with the third they support a self (from IKEA or other) and the other two support two keyboards. A small laptop table can be used for pc-keyboard or a use dedicated part. It solved the computer problem which requires a piece of furniture or a table with min cost. The pc has software instruments which can be synchronized with keyboards in an integral way. Nice for home studio. One disadvantage. It is large as it can handle 88-note keyboards and needs a whole wall to stand against at not too much footprint. But it makes sense to do it. Most configurations can be obtained with such a flexible equipment. The size depends on the keyboards though. Perfect ergonomy: Height and position of keyboards, height of computer screen, height of speakers (independent stand but fit inside). Sturdy. Wheels are removing anxiety in a minute with the whole build going back and forth with a finger. 10/10
Top self was put in the back and with the third they support a self (from IKEA or other) and the other two support two keyboards. A small laptop table can be used for pc-keyboard or a use dedicated part. It solved the computer problem which requires a piece of furniture or a table with min cost. The pc has software instruments which can be synchronized with keyboards in an integral way. Nice for home studio. One disadvantage. It is large as it can handle 88-note keyboards and needs a whole wall to stand against at not too much footprint. But it makes sense to do it. Most configurations can be obtained with such a flexible equipment. The size depends on the keyboards though. Perfect ergonomy: Height and position of keyboards, height of computer screen, height of speakers (independent stand but fit inside). Sturdy. Wheels are removing anxiety in a minute with the whole build going back and forth with a finger. 10/10
0
0
Report
A
Wonderful, sturdy stand - arrived quickly
I placed 6 of my synthesizers on it, my main being the largest and most heavy, on the bottom layer - after putting it together, which was fairly simple to do. Its been a couple weeks now, I think. Very happy with this stand! Thank you so much - and thank you Jaspers - these specific type of multi synth stands seem harder to find in the USA.
0
0
Report
M
Fantastic, adjustable, flexible, solid, and dependable, BUT be sure to inspect and retighten the bolts!
This was a solid stand for me for 3 years, top manufacturing and flexibility. I have been very happy with the investment in this model! But, I would encourage everyone to inspect and retighten everything on your rack, once or twice a year. Recently I rearranged my stand and shifted some gear across the bars and changed the height of the middle two racks, and after having been stable for the preceding 20 hours, something happened while I wasn't present in the room. Something either slowly slipped down and shifted or a Tube Clamp Joint failed, and my stand tipped forward onto the hardwood floor, dumping all my gear with a few unfortunate but repairable casualties. Inspecting afterwards, a fiber-reinforced Tube Clamp Joint was found to fractured/broken, but I can't say if it just failed (unlikely) or if it was broken by the force of the stand hitting the floor (more likely due to the torque & impact). Previously, I had inspected the center of gravity while I was loading my gear onto the rack, and the lowest shelf had a similar amount of weight on it (~30kg) as it had for the previous 3 years, and it had been stable for the preceding 20 hours, so it's a mystery. I have ordered some additional Jaspers stand parts to replace the damaged Tube Clamp Joint, and provide some additional cross bracing and redundancy for potential future slipping. But all in all, I have been super happy with this stand! :)
0
0
Report
JE
Jaspers Stand
Very well made, easy assemble, this is a quality product
Been searching for something like this for a while and even though had to ship to Australia from Germany it was worth it
Been searching for something like this for a while and even though had to ship to Australia from Germany it was worth it
0
0
Report
