Harley Benton Electric Guitar Kit CST-24

I have a lot of guitars but wanted to try “assembling” a kit. There are quite a lot about but this is the cheapest and with Thomann guarantees the safest bet. I liked the simplicity of the non-trem version and the fact that the headstock was pre-shaped and rather pretty. The tuners are cheap and what would spend money first to replace but they do work. the felt pretty rough so I took off the buttons, attached them to a drill, filled them up with light oil and span them backwards and forwards to try and bed them in. Workable. The nut is plastic and moulded, not cut. The neck pocket was slightly too big so I glued a shim of veneer to one side and that was much improved. The body looks quite nice and is coated with a pore filler sealer. If you want to oil or stain you will have to sand this off. A lot of work. I started to sand it in preparation for primer and paint but decided not to bother. It looks and feels very good especially with the binding. The pickups are pre-mounted in the rings but the ring screw holes do not match up with the pre-drilled holes. Easy fix. Same with the jack plate. All the electronics are cheap, pre-wired and have push fit connectors. No soldering required. The bridge was easy to install and cast for basic intonation with a slidy piece for the B and G strings. Overall intonation can be set with grub screws on the ear to post attachment. I have a lot spare parts: pickups, nuts, pots, caps, treble bleeds but in the end I decided to assemble it as it came to provide a datum point before modding and to see how it felt and sounded just how it came out of the box. I even used the strings supplied.
I was blown away by this guitar.
So were my sons. And my mates who I didn’t tell what it was. Should have seen their faces when I said it cost £75. I had to show them the listing on Thomann before they believed me.
The guitar is light, comfortable and a delight to play. The neck is gorgeous and worth more than the kit price on it’s own. The fret ends are good, no high spots and not rough. No work required. The fretboard sucked up a lot of lemon oil at first. All in all aside from the neck pocket it took about 90 minutes to assemble. I will be modding it but for now it’s actually a joy to play. You will need some basic skills to get the best out of the fit and finish but that’s what something like this is all about. It’s a learning experience. My friends 15 year old daughter loved and is going to order one to build with her Dad. Whatever happens it is so cheap who cares and if something is really unacceptably bad, send it back. Buy it, try, have fun.

Body. Quite a laborious process of removing the preservative varnish. The scale length is 24 and 3/4 instead of 25. The cutout for attaching the neck must be fixed, otherwise the lower strings will ring - lifting the bridge does not solve the problem. My rating is 3/5.

Pickups-do not correspond to those in the picture. I got pickups in a metal screen. The sound is really good. My rating is 4/5.
Potentiometers, strings and pegs-of satisfactory quality, 3/5.

And finally, the hero of my review is the neck. In the kit for self-assembly of the guitar, the neck is the most important part. The need to polish the frets can not reduce my rating, it is traditional. However, in my set, the neck has an irreparable defect - there is a bitch exactly in the middle of the neck. Therefore, 4-6 strings after the middle of the neck emit sounds that can be described as the beating of two tones. It is impossible to play on such a neck. My score for the most important part is 1/5.
It seems that self-assembly kits are completed with parts rejected at the factory in the absence of control from the store Thomann.
Result. A set worth 170EUR, including delivery, will go to the trash.

So, I was oogling this kit for months and I finally managed to claim it. I am going to give a detailed review of the whole process of assembly.

First off, packaging. Very well, very securely done, except for a very small dent in the back, however with the roads and vehicles that drive around delivering packages in my country, I am surprised it's only one and is miniscule.
The wood is sealed very well, although I would put another 2-3 layers just in case, as well as to bring out the grain a bit more, but that's just my kink. Solid 4-5 piece body(dunno if i counted right).
Fittings and holes. Almost perfect. The neck went in like a glove and no work on it was needed. Holes for the parts were made perfectly, with the exception of the bridge holes, where I had to hammer them quite much, until they go all the way in. Seeing as hammering is even in the manual, again I see it as normal.
The neck itself is beautiful, no sharp frets, straight and beautiful. I only needed to touch the nut just a bit so the strings would fit more securely.
Pickups are different than the ones on the image. I got metal plated ones, instead of the waffles, however it was actually easier to figure out what goes where and how. In terms of sound they are extremely well for my taste.
I've read a lot of Harley Benton kit reviews that have the same grievances about not enough detailing on the wiring system and 'guess work' wiring. While true, in this case you can somewhat find your way by the length of the cables in correspondence with the holes, so not entirely a big deal.
There is only one thing that really irked me, and that was the strings packaging. They were bundled up and knotted so much and so tightly, that I had a very difficult time separating them, resulting in one string having a bend, that I somewhat fixed upon setting up. Still, it's not something that takes away from the quality of the guitar itself.

Overall, this is my first DIY guitar and the way it sounds, all stock and everything, is simply amazing. Everything is tight, solid and works well. For me, it's good to go as it is, and should I wish to upgrade, now I know how to do it.

I bought this kit with the intention of using only the body and neck. I replaced the pickups for a Seymour Duncan set and added inexpensive locking tuners. The supplied electrics were well soldered and worked well, but I swapped them as I wanted a push/pull coil split option (this is the only reason I reduced the 'features' rating from 5 stars to 4). Despite the body wood being quite soft and the bridge being quite light, it sustains well. The neck is beautiful. I didn't need to dress the frets or adjust the truss rod. I just cleaned it and added lemon oil. The wraparound bridge required only a couple of turns to set the intonation and the action is low and with no fret buzz at almost the lowest setting. I own 4 other guitars (all way more expensive) and this is by far my favourite. I was so impressed, I've ordered another, which I plan to paint and use the supplied pickups and electrics.