Sonarworks SoundID Ref Spk & HP w Mic EDU

20

School version

ATTENTION! This software version can only be purchased under certain conditions set by the manufacturer! Please be sure to read our notes on EDU conditions in the "Smart Navigator" at the bottom of this page before adding the item to your shopping cart!

Bundle of measuring microphone and software for loudspeaker and headphone calibration

  • Frequency response correction for studio monitors and headphones for the most linear reproduction possible
  • Enables better assessment of recordings and mixes
  • Room analysis and automatic room size calculation using numerous measuring points
  • Audio Calibration Engine for the most accurate adjustment possible
  • Any number of profiles for loudspeakers can be stored
  • Comes with calibration curves for over 280 different headphone models
  • Target curves can be individually adjusted in real time
  • Translation Check simulates more than 20 different devices and device types for the accurate realisation of a mix
  • Three selectable filter modes: Zero Latency, Mixed and Linear Phase to optimise filter quality and latency for different listening situations
  • Additional settings for mono, dry/wet and safe headroom
  • Only available in the app: MIDI mapping for various parameters and user presets for predefined output configurations
  • Measurement microphone with pre-polarised electret condenser capsule
  • Frequency range: 20 - 20.000 Hz with measurement protocol
  • Polar pattern: Omnidirectional
  • Sensitivity: 14mV / Pa
  • Inherent noise: 24 dB
  • Signal-to-noise ratio: 70 dB
  • Dynamic range: 106dB
  • Maximum sound pressure level: 132 dB SPL
  • Requires 48V phantom power
  • Connection: XLR 3-pole
  • Calibration file for 30° off-axis measurement in native Sonarworks format for use with SoundID Reference software
  • Calibration file for 0° on-axis measurements in TXT format
System Requirements
  • Shipping Format: E-Mail
  • License validity: perpetual
  • Copy Protection: Online Activation
  • Simultaneous Activations: 1
  • Windows: from 8 (64-Bit)
  • Mac OS (64 Bit): from 10.12
  • add. System requirements: Internet Connection for Installation and Activation, calibr. Headphone
Supported Formats
  • Stand-Alone-Software
  • AAX native 64-Bit
  • AU 64-Bit
  • VST2 64-Bit
Available since March 2021
Item number 515341
Sales Unit 1 piece(s)
Audio- / Effect Plugin Yes
Audio-MIDI-Sequenzer (DAW) No
DJ Software No
Mastering Software No
Notation Software No
Updates/Upgrades No
Misc. Musicians Software Yes
Virtual Instrument / Sampler No
2.280 kr
Including VAT; Excluding kr200 shipping
In stock
In stock

This product is in stock and can be shipped immediately.

Standard Delivery Times
1

20 Customer ratings

4.5 / 5

You have to be logged in to rate products.

Note: To prevent ratings from being based on hearsay, smattering or surreptitious advertising we only allow ratings from real users on our website, who have bought the equipment from us.

After logging in you will also find all items you can rate under rate products in the customer centre.

handling

features

sound/quality

computer utilisation

14 Reviews

J
Buy this, save £1k by not buying new speakers
JoeO 18.01.2022
I've had my HS7s for about 4 years and was looking at upgrading to something like Adam A7Xs etc but decided that ultimately, theres no point buying new speakers if my room isn't right. I don't have the luxury of being able to properly treat my room so I got SoundID instead, thinking at least it will help somewhat before I can get a more permanent setup. Genuinely, this is amazing.

As long as your speakers are already in the right place, it takes about 20 minutes to setup. The process is fairly simple and the software guides you every step of the way. If you mess up you can go back and repeat a step anyway. After you've finished measuring your room you get a graph depicting how accurate your speakers are currently. Despite not having any treatment, I always thought my speakers sounded ok. Turns out I have (had) a -12dB notch at 90Hz and have a number of 3dB peaks and troughs across the low mids. I went through all my favourite reference tracks and was blown away. You can A/B really easily with the software and hearing how I normally listen vs how things are 'supposed to sound' was quite eye opening. The only slight con I have noticed is that keeping the software on 24/7 drains my battery slightly more than anticipated. However, in all fairness I am due a new computer fairly soon (2016 MB Pro).

The only downside is that now all I have to blame are my bad mixing skills!
handling
features
sound/quality
computer utilisation
3
1
Report

Report

G
Excellent calibration features!
Gorbz 16.08.2021
This piece of software (and mic) does an excellent job to flatten my studio monitors as well as my headphones. My only complaint is that is gets confused as to what my interface is when I switch on my AXE-FX III and then I have to restart it sometimes.

All in all, excellent product.
handling
features
sound/quality
computer utilisation
0
0
Report

Report

M
Works great
MassMic 06.12.2022
Obviously not a substitute to an acoustically optimized room, but even when so, a positive difference is heard. With headphones, you can get the ultimate flat sound you need. The better the heaphones, room, or speakers, the better your sound. SoundID gives that extra push.
handling
features
sound/quality
computer utilisation
0
0
Report

Report

R
Effective Plugin
RonWC 26.02.2024
This plugin has definitely made a difference to how I hear my mixes. I use it as a plugin within Sonnox ListenHub, which lets me switch between monitors and headphones. I feel that the mix now translates well between the monitors (Adam T5V) and the headphones (Beyerdynamic 880). It has also really helped me to place the acoustic treatment in my room. Overall, a worthwhile investment. Hasn’t made me a better mixer unfortunately!
handling
features
sound/quality
computer utilisation
0
0
Report

Report

YouTube on this topic